Recent Activity

Activity stream for all registered members at DF Kit Car Forum.

  1. canyon bolieu replied to the thread Canyons trackframe LSJ-T Htown.

    So I have seen some of you talking about cutting your tunnel in 3 pieces how is that working for y’all and how are you guys fastening it...

    Nov 19, 2017 at 11:54 PM
  2. George replied to the thread Shadow Lou Racing, street,track,autocross Goblin.

    Did very little this week, clean and tested fuel injectors. Thought about how to add anti squat to rear suspension. Waiting for pistons...

    Nov 19, 2017 at 1:58 PM
  3. Briann1177 attached a file to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    I guess you could also measure the output resistance of the clutch sensor. I measured mine and it was like 1.4k Ohms with the clutch...

    Clutch.jpg Nov 19, 2017 at 8:50 AM
  4. Tony replied to the thread Tony's City Goblin - 2010 SS/TC.

    Funny story, I now work at a CNC shop haha. Might be able to get some negative molds machined out of steel and just do some permanent...

    Nov 18, 2017 at 11:48 PM
  5. JeffsGoblin replied to the thread Exhaust Valve Help....

    Thanks everyone! I'll test and most likely start with new valve seals.

    Nov 18, 2017 at 11:30 PM
  6. JSATX replied to the thread Tony's City Goblin - 2010 SS/TC.

    That’s a nightmare. You’re better off having a local cnc shop knock it out if you really want it in aluminum.

    Nov 18, 2017 at 9:34 PM
  7. BaltimoreHokie replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    Yeah. I've tried that...always the same result. Wont turn the starter. Its like whatever tells that relay to open is not happening.

    Nov 18, 2017 at 7:25 PM
  8. Briann1177 replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    Try swapping that relay out. You should be able to swap it out with a relay from an unused circuit like wiper on/off or rear defog.

    Nov 18, 2017 at 7:22 PM
  9. George replied to the thread Tony's City Goblin - 2010 SS/TC.

    Question, what about print it in PLA and use it in a lost wax aluminum casting for the part that must handle heat. Brad

    Nov 18, 2017 at 7:15 PM
  10. BaltimoreHokie replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    Yeah. It wasn't running when I got it so I wanted to see if the work I had completed fixed the issue. Now. Just to figure out this...

    Nov 18, 2017 at 7:14 PM
  11. Briann1177 replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    Sounds like you're getting close to pinning it down.

    Nov 18, 2017 at 7:12 PM
  12. BaltimoreHokie replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    Yes. But basically right after it was running I had her turn it off prob no more then 4 seconds idling. Tomorrow I'll put the manifold...

    Nov 18, 2017 at 7:05 PM
  13. Briann1177 replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    So you jumped the crank relay while your wife cranked it over and it idled for a bit?

    Nov 18, 2017 at 7:03 PM
  14. BaltimoreHokie replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    I had the manifold off because of a fuel leak that I fixed. Before I found the leak it wouldn't turn over. So I replaced the starter and...

    Nov 18, 2017 at 6:54 PM
  15. Briann1177 replied to the thread Donor Help - Cobalt SS wont start but cranks - Thoughts?.

    You have the intake manifold off? :confused: That's probably part of the problem with the idle. I'm surprised it would even run at all.

    Nov 18, 2017 at 6:51 PM
Loading...