Search results

Gtstorey, I appreciate the help, but I have the diagram. That is what I used to help me trace this down.

I think I have traced down the cause of my problem. I put a volt meter on the wire that goes from the park/neutral position sensor on the transmission to the ECM. I'm getting 0 volts whether the trans is in park or reverse. I'm thinking there should be a signal on that wire when the trans is in...

Gtstorey, I get what you are saying about the data being sent on the BCM data wires and maybe a voltmeter isn't the best way to measure that. I already checked ECM X1 pin 32 which is the wire that sends the signal to the starter to start. Currently, that wire has 0V on it when the key is turned...

Gtstorey, I found your chart. Here it is. All my voltages line up with yours, except the white wire (pin 5). I'm getting 12V with the key in. 4V at Run. You didn't list a voltage for Start but I'm getting 3V. I gut tells me that the Start voltage should be 12V. As I said above, the voltage on...

Guys, I'm trying to troubleshoot this starting issue. I got a diagram of the ignition system and I decided to start with the ignition switch. According to the diagram a white wire that runs from the ignition switch to the BCM is the wire that tells the car to start. There are two data wires that...

Starting Issue - 2009 non turbo engine, auto trans Guys, I need some help. My engine install has been done for months and the engine has been running fine. I'm near the end of my build and suddenly I have an starting issue. This morning I went out to start up my Goblin, turned the key. The...

Yeah, I figured that out looking at some photos. Originally I had it backwards because I assumed the bleeders would point down but the parking brake levers won't work that way.

Oh I see now. Those brackets are in the parking brake kit which I haven't starting messing with yet. Thanks for your help.

Folks, I need some help. Trying to work on the rear brakes. When I went install the rear calipers, nothing lines up. In the two attached pictures you can see that the spacing for the caliper mounting holes on the spindle is about 5". The spaces for the mounting holes on the calipers supplied by...

Rttoys maybe I'm blind, but I'm not seeing the answer to my question in the link you provided. That thread seems to be all about the brake lights.

Headlight Question Fixing to install the headlights. The actual install of the headlights on the Goblin seems straight forward enough. My question is in regards to the wiring. My Cobalt wiring for the headlights has five wires on each side. The driver's side has yellow, green with white stripe...

Jamesm, thanks for the reply. It's been over a year since I striped my Cobalt. I completely forgot about that part. Makes total sense now. ' Thanks.

Steeling Wheel Install Question Guys, I decided to try and get the steering wheel installed. I see how the steering column hardware gets installed on the frame and extends toward the inside of the Goblin with the shaft in the middle of it. Thing is, my steering wheel shaft doesn't even extend...

Ok. I see where these are supposed to go. I actually reused the donor transmission mounts front and back, and have those bolted in so I think I'm good to you with this. I'll just put these parts to the side. Thanks for reply.

2009 LS Auto Solid Transmission Mount for Auto Guys, I recently finished the last build video, #24. I was going thru the parts that I have left and came across these two metal brackets (parts P11O and P11P) and a hardware bag (part N15M) that are all labeled Solid Transmission Mount for Auto...

Hey guys, I don't want to waste anyone's time. As soon as I sent that last post, I walked back out to the garage and turned the key. It started up and it's staying running. Maybe it just needed to get gas all through the system. Anyways, at the moment I think I'm good. I'm going to be starting...

Ok guys. I appreciate all your quick responses. Looking over all your comments, Ross's comment about it being in Park made a lot of sense to me. If it's not in park it's just not going to try and start, which is what I was dealing with. So I went back to the transmission cable. I thought I had...

2009 LS automatic First Start - Nothing Ok guys, I just tried my first start and it didn't go well. I'm jumping the battery since this Cobalt battery hasn't been used in a year. I have power on the dash. Fuel gauge went up as I added fuel. I was able to jump the fuel pump to purge air out of...

So it's not used. Perfect. I definitely had a couple wires crossed, but I think I have it figured out now with your help. Thank you so much.

Ok guys, I think I'm making some sense out of this. When Chris said power steering that jogged my memory. I remember that plug was for power steering. I just traced the thick red wire with a black stripe coming off my power steering unit back to the fuse box and I currently have it connected to...