Search results

I broke my axle the exact same way this past weekend at autocross. I just installed the new subframe and just before the event and didn't realize how far it stretches the axle on the driver side. Has anyone else been having axle issues with the new subframe? Edit: Spoke with lonny and he said...

They did require a bunch of stuff that I worked with the inspection station to get done. I have to have the engine covered, bumpers, 4 corner marker lights, as1 glass with wiper. They just went away after I got the plate

Yeah i got my goblin registered in PA last year and it was fairly simple. The biggest thing is finding a really good inspection shop. I got my inspection done. Waited a few months with no response from PennDot, Decided to call and ask using the id they stamped on the check and got a call asking...

Oh it was definitely my fault, I've been slowly learning to tune on it so didn't spot the narrowband not lining up with the wideband till a lot of diagnosis

The leading theory is that the engine was running really lean for a while. I was struggling to tune it for months because the AFR never seemed to be right. Turns out the WB o2 sensor was bad and giving me inconsistent readings that always seemed to be just out of reach (Within 5-10% but never...

I've had a few issues with it. which one in particular are you curious about? The latest issue I discovered was a warped/burnt valve in cylinder 2 causing it to have no compression. The car is currently torn apart for the Fueltech install and the head is being rebuilt/ported by Josh over at...

I look forward to it! feel free to ask for any help as I'm relatively nearby!

It is a very similar color inspired by the donor yes. The color is from Prismatic powders called Illusion rootbeer I ran in XP because when I called and asked my local region the told me to run in XP since we have a couple other XP cars I could compare my times to. They said I would need to...

I can stand on my splitter and it deflects maybe 1/2 inch. I'd say the 1/8 is plenty. I put two rivnuts in the rad support and got some conduit straps with radiator hose in it to clamp over the lower frame rail.

It is made from 1/8inch 5052 aluminum

Well I thought that last post would be the last race of the season for me but I managed to shift my schedule around to run one last time on November 4th. I drove the goblin about 10 mins to the event at 6am while it was only 34 degrees outside. With the footwell cover removed the drive was...

I'm not very good at this forum thing but I've got some time and guess its a good time for an update. My goblin was officially a legal car as of May 17, 2023 when I got the title plate in the mail. Since becoming legal I have put about 1200 street and track miles on the car. Not to much has...

Final event of the season for me went amazing! I am finally getting a hold of this car with the help of multiple local racers getting behind the wheel and giving me lots of great advice. Here is my 73 second XP class winning run at Pocono raceway last sunday. I was not very high on the raw...

Maybe not next season but hoping to get up there and be some competition for ya! PA has a lot more hillclimb opportunities for practice till I decide to make the long trips to the Appalachian series! Great driving as always Justin! definitely and inspiration.

I'm not sure what the min ETC area does to be honest. I didn't change that setting, had a guy helping me with tuning a while ago but wasn't working out. I'll try changing it back to zero though tomorrow!

I have changed the ETC scalar a while back because I had trouble with it pulling timing into the negatives at idle. The p12 ECM on the lsj does not have the base running airflow table unlocked in hp tuners and with the larger cam it struggled at low airflow/efficiency. by boosting the ETC...

That’s what I thought at first too. Couldn’t find anything obvious… I don’t have a proper smoke tester so I am open to any recommendations. Tried some hairspray around the intake since I was out of parts cleaner lol. I’ll pick some up in the morning to see if it’ll make a difference

Right right! Here is the latest on the tune. I had put many miles on this before pulling the intake off and fixing the pcv. Notable changes since the last tune I posted is the addition of a boost reference fuel pressure system. The low end of the maf is from today trying to get it to idle...

Well, The issues have returned after I chased down that my pcv valve was stuck open. I found the source of my KR from earlier being a bolt that came loose on the HE pump bracket. Now that the engine is all back together I'm struggling to get it to idle down to where it was previously. I've...

Hmm ok I’m. It sure then. Sorry for the rabbit chase.