Search results

Good Morning, I had continuous issues with the o-rings leaking. So with the new engine build replaced the OEM dipstick with an aftermarket one. THX, Bruce

Take a look at my build thread... using stock sliders with FX1 seats...

Good Morning, Would like to get $500 or BO (they are like new and have the universal side mount flanges also). THX, Bruce

Good Evening, Last of the bigger items... (1) Fiberglass Lotus 7 nose cone... (2) Large fiberglass air intake was going to cut up and use for side intakes... (3) Main fuse block housings... (4) Misc. fuse blocks... THX, Bruce A lot of parts listed above through out this thread... I...

Good Afternoon, Just working through the wiring harnesses... (1) Complete supercharged Cobalt chassis wiring harness... (2) 2008 Cobalt Engine harness (automatic transmission all labeled)... (3) “BLUE”s initial wiring harness (was in the process of removing the transmission portion -when...

Good Morning, The injectors are the stock (OEM) 2.2 Ecotec one. Just the one I removed when I installed the supercharger.

The parts listed above just scratches the surface. We probably had enough parts to build a third and close to a fourth car.... (plenty to finish Nate’s mega motor Goblin)... If you need anything shoot me a message and I’ll see if I have it... THX, Bruce

Good Evening, Last one for tonight... I’ll get into the harnesses tomorrow... (1) 2 complete electric steering boosters plus 2 addition motors... (2) 2 complete brake boosters with new master cylinders... (3) 3 different emergency brake handles... (4) OEM steering wheel assembly and OEM...

Good Evening, Additional... (1) QA1 #300 springs and new strut boots... (2) 5 3/4” headlights, Coolant tube for Non-turbocharged engine, Set of engine bolts from a new engine that were replaced with studs... (3) 2 Sets of lug nuts 1 set short, and 1 set long, wheel spacers... (4)...

Good Evening, Additional.... (1) Complete cable driven windshield wiper set up... (2) Couple of new mufflers... (3) Exhaust set up I initially used on “BLUE” overheated the catalytic converters (bad initial tune with the supercharger). So the catalytic converters is hallowed out... (4)...

Good Evening, Here are a couple more... (1) 2 sets of rear wing (spoiler) mounts... (2) Couple of catch cans... (3) 2 sets of computers... (4) Set of powder coated brake calipers (with pads and rubber lines)... (5) Ended up I did have 2 individual seat tracks (different manufacturer)...

Good Afternoon, Just going to load additional pictures as I pull parts out and photograph... (1) one sliding seat track (only put a slider on the drivers seat in “BLUE” (2) brand new cam for a 2.4 Ecotec (pulled to replace with performance cams) (3) Sway bars (stock and one from a...

Good Afternoon, Just trying to open up some additional space. As I pull stuff out I’ll photograph and list here. (1) 2010 Ecotec 2.2 with 7,000 original miles (2) numerous wiring harnesses (1 complete body supercharged may have the engine also) 2 complete 2.2 automatic wiring engine/body...

Good Morning, Got the new engine mated up to the transmission and all set in the cradle. You can also make out the stand alone harness (also wired for a complete electrical gauge package).... Biggest question will be with regards to the fuel system. Will we need to upgrade the stock OEM fuel...

Well Good Morning, Nate’s Goblin has been mothballed in my basement for the last year between school and the restrictions for him in the dental clinic not a lot has happened on it. So looking around at all the additional parts (mostly higher performance) that initially were going to be...

Good Afternoon, Does the F35 utilize the jack shaft. (Or intermediate axle)??? Similar to the F40. Working on something and am trying to keep the two axles basically the same length. THX, Bruce

Good Evening, I actually have a Lotus 7 fiberglass nose cone that I was playing with (but never fully fitted it to either of the Goblin frames). Probably should start to get rid of some of the extra parts that I most likely won't be using if your interested. On the road currently, but I'll get...

Good Afternoon, Bit the bullet and drained the oil... Auto meter oil temp prob threaded right in to that plug in the oil pan. (So either it actually is a 1/8NPT or the brass prob adjusted to a metric tread size that’s nearly the same size???). So that makes life a little easier. Bruce

Good Evening, Just doing some finishing up of the engine. Installed a pressure sensor with a 12x1.75 to 1/8 NPT adapter. I also wanted to add a temp sensor but have not been able to find a deep enough adapter (temp probe bottoms out in a normal adapter). If I was smarter would have drill and...

You wouldn’t be interested in selling the LNF one would you? Have a call into Adam to see if I can buy one from them also....