Menu
Home
Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
Gtstorey's latest activity
G
Gtstorey
replied to the thread
What would you order for a street oriented canyon carver?
.
Today at 7:11 AM
G
Gtstorey
replied to the thread
Insurance choices.
.
I'm sure I read some post on here discussing how they got Haggerty insurance through Progressive after Hagerty turned them down.
Yesterday at 3:03 PM
G
Gtstorey
replied to the thread
Ross's extended city, easy entry Goblin- 06 SS/SC, NW Arkansas
.
I would probably start by moving the entire front suspension over, from A arms out. If the cars are supposed to be identical both sides...
Yesterday at 2:57 PM
G
Gtstorey
replied to the thread
Ross's extended city, easy entry Goblin- 06 SS/SC, NW Arkansas
.
It's time to have another full Goblin without the problem with you and start swapping assemblies over one direction or the other until...
Yesterday at 7:51 AM
G
Gtstorey
replied to the thread
Nukers City Goblin - 2009 SS/TC number 2 build
.
Crank sensor is #7 in first picture. Sensor connector is second picture. You are likely missing the jumper harness in third picture...
Tuesday at 6:11 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
I've ordered one for mine, but it will be setting so close to the sensor I'm not sure what it will do. The face of the sensor is 1.5"...
Tuesday at 1:18 PM
G
Gtstorey
replied to the thread
Nukers City Goblin - 2009 SS/TC number 2 build
.
It looks like you grabbed that image from Rockauto and it doesn't look like familiar. Look at the ACDELCO/GM male connection at see if...
Tuesday at 1:11 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
I don't think it's causing a vacuum because it looks like more air is passing through, at least the MAP goes up. I think it must cause...
Tuesday at 12:46 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
I wish I knew enough about tuning to speculate what might be going on. The MAF thinks less air is going through causing it to cut fuel...
Tuesday at 7:47 AM
G
Gtstorey
replied to the thread
Air Filter Placement
.
How about throttle/RPM? I assume that's light throttle/cruise since command ratio is 14+. 18:1 is LEAN and it looks like that might just...
Monday at 4:17 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
What's the horz. scale of your graphs above? Was that a few seconds or a few minutes?
Monday at 3:38 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
Another thought is was your maf tune set up for the first location? Your graphs looks to me more like it was actually moving more air...
Monday at 2:36 PM
G
Gtstorey
replied to the thread
Air Filter Placement
.
K&N increases the tube size to 3.25 for the short section where the MAF is mounted and obviously no straight section after the MAF. All...
Monday at 11:58 AM
G
Gtstorey
replied to the thread
Air Filter Placement
.
Hopefully mine is closer to Ross's first post than Chad's, although I'm a little worried about the lack of laminar flow. The MAF hasn't...
Monday at 8:48 AM
G
Gtstorey
replied to the thread
Ready to start, but. . .
.
Just to be clear on you coil pack picture, there are 4 of them across the top of the motor, with 1.5 showing in your picture. It's hard...
Mar 31, 2021
Home
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top