**Post Pictures of your Finished Goblin Here**

[Ghostknife]

The nice part about Colorado is, it’s not far from Montana…..

 

[Rttoys]

A dunebuggy with 4 inches of ground clearance, yeah right boneheads. Montana doesn't have this problem.

Yep. That what I tell people when they say it’s a dune buggy.

 

[Ark :D]

Pretty sure Montana will register anything with a couple wheels and a horn...!

 

[Adam in CLE]

colorado flat out told me no because it was a dune buggy...so if anyone runs into these types of DMV clown I suggest contacting SEMA's legal department and writing letters to every state representative.

Wow. Are you going the Montana LLC route or do you have another option?

 

[Christopher Sanchez]

My guess would be that most people have had similar responses from their local DMV staff. I was told mine could not be registered for the street as it was an OHV.. All you can do is politely disagree and visit another DMV nearby or come back another day. The key is to come 100 percent prepared with all paperwork including literature printed from your state’s website explaining the requirements.. Once you show the facts and show you’re knowledgeable about this process eventually you will find someone actually willing to help. Don’t give up. Good luck!

 

[Goblinfanclub1234]

Wow. Are you going the Montana LLC route or do you have another option?

all my final paperwork was sent into Montana DMV a couple weeks ago so any day now!

 

[BSinvestments]

My new to me, slightly revamped Goblin #74

 

[Desert Sasqwatch]

Interesting that no intercooler is mounted in the normal position on top of the engine, but has a BOV in that location? Are you not running an intercooler? I'd have to believe the ECM is pulling timing from the motor with the high IATs created by a direct feed from the turbo? One of the photos shows your Goblin on a dyno - what are the numbers?

 

[Sluggonaut]

Interesting that no intercooler is mounted in the normal position on top of the engine, but has a BOV in that location? Are you not running an intercooler?

The piping suggests he is using an LSJ intake so likely using the normal SC intercooler config.

 

[BSinvestments]

Interesting that no intercooler is mounted in the normal position on top of the engine, but has a BOV in that location? Are you not running an intercooler? I'd have to believe the ECM is pulling timing from the motor with the high IATs created by a direct feed from the turbo? One of the photos shows your Goblin on a dyno - what are the numbers?

The piping suggests he is using an LSJ intake so likely using the normal SC intercooler config.

This is correct. This car is an LSJ running the factory manifold with air to water using a zzp s3 heat exchanger in sync. On a 90+ degree humid day on the dyno it maintained ~130° iat2 temps.

 

[Desert Sasqwatch]

Ah, okay, my bad. Thought you had a TC donor. (feeling stupid, I'll go sit down now).

 

[BSinvestments]

Ah, okay, my bad. Thought you had a TC donor. (feeling stupid, I'll go sit down now).

No way! I’ve learned more from reading your post on this forum then I could ever find online.

 

[Goblinfanclub1234]

You can tell it is an LSJ by the rectangular coil cover, the LNF cover has a lot of cutouts for the coils

 

[PHENDERSON]

Finished just in time for MN winter.

 

[Robinjo]

 

[Goblinfanclub1234]

yes I am putting an LS6 in a 1988 Nissan Sentra. I love this sentra. Zero rust on the chassis. Elegant engineering. My goal is to go 10's in this beauty in 100% sleeper mode. I am grafting in mazda miata MX5 front LS swap subframe with a miata rear subframe and suspension. just have to learn how to mig weld first. these late 80s japanese cars are like JDM fox body gems. I love this car so much i just want to hug it.

 

[Josh's09]

Just put them on.

18x11, +15 Konig Hypergram with 1.5” adapter/spacers. Tires are 335/30/18 R888R’s.

Originally had 18x9, +44 Flow One F1’ with 1” adapter/spacers and 245/40/18 BFG Sport Comp2

Do you have any pictures of the goblin (love how this came out btw) from the side? I am looking to purchase the same wheels (but with a different finish)? I haven't been able to picture it, Would love to see some pics if you got any!

 

[Rttoys]

Do you have any pictures of the goblin (love how this came out btw) from the side? I am looking to purchase the same wheels (but with a different finish)? I haven't been able to picture it, Would love to see some pics if you got any!

.

 

[Poolerboy]

This was so much fun to build as well as to drive it this thing really moves .. it was starter for me to see if I can handle it before going crazy on A more expensive build like an ac cobra View attachment 15859View attachment 15858View attachment 15857View attachment 15856View attachment 15855

Where did you get the roof rack.

 

[escapepilot]