V1 PyroGuy's '08 SS/TC Build - #208 - REGIRSTERED!

[PyroGuy923]

Look for G85 on your trunk plate to verify.

Sure does. Thanks.

 

[PyroGuy923]

Got the rest of the donor body stripped over the weekend. Just have the dash left.

 

[JeffsGoblin]

Got the rest of the donor body stripped over the weekend. Just have the dash left.

Don't forget to grab your e-brake cables, e-brake tubes and e-brake handle assembly if you are going with DFG's e-brake solution. I noticed your cables were still there. I didn't know I had to keep the tubes or cables when I stripped my donor, so I had to source them again!

 

[Zoom Zoom]

Don't forget to grab your e-brake cables, e-brake tubes and e-brake handle assembly if you are going with DFG's e-brake solution. I noticed your cables were still there. I didn't know I had to keep the tubes or cables when I stripped my donor, so I had to source them again!

Did you buy the little plastic tips some where, mine fell apart when I took them out

 

[JeffsGoblin]

Did you buy the little plastic tips some where, mine fell apart when I took them out

I went to pick-and-pull to get another set and tips were fine. I doubt if you can get the tips by themselves, unless you try pick-and-pull.

 

[PyroGuy923]

Don't forget to grab your e-brake cables, e-brake tubes and e-brake handle assembly if you are going with DFG's e-brake solution. I noticed your cables were still there. I didn't know I had to keep the tubes or cables when I stripped my donor, so I had to source them again!

Got them when I stripped the rear. Thanks.

 

[PyroGuy923]

Any idea the specs on the clutch position sensor bolt?

 

[Ark :D]

M4 X 0.7

 

[PyroGuy923]

M4 X 0.7

Thanks.

 

[PyroGuy923]

Finally bit the bullet and ordered my kit.

 

[Desert Sasqwatch]

You are chassis number 208?

 

[PyroGuy923]

You are chassis number 208?

Not sure. Didn't see it in the order or in the email. Will post when I get confirmation.

 

[JBINTX]

wahooooo!!!!!

 

[PyroGuy923]

Yup, chassis 208!

 

[Zoom Zoom]

Congratulations to you.
My Goblin 189 might be here today or tomorrow haven’t heard from driver.
Adam said they were picked up and left there place around 5 PM ON MONDAY AND THAT IS ALL I KNOW.
WHEN THEY WILL GET HERE WHO KNOWS

 

[PyroGuy923]

This waiting game is going to kill me. I should have ordered my chassis weeks ago.

What maintenance items do you recommend I do before assembly? Donor has 126k on it.

I know the timing chain guide bolt is cheap insurance.

 

[Rttoys]

1. Make sure everything is clean and painted how you want.
B. replace spark plugs, oil filter, oil (if you can get to the drain plug), belt, check tensioner.
III. Thin out engine harness
d. Make sure everything is clean and painted how you want.
5. Make vroom vroom noises

that might be it.

 

[Ross]

This waiting game is going to kill me. I should have ordered my chassis weeks ago.

What maintenance items do you recommend I do before assembly? Donor has 126k on it.

I know the timing chain guide bolt is cheap insurance.

Timing chain tensioner is a common Ecotec failure. A new tensioner has a bolt head that bulges out, the old stock one has a flat head.

 

[PyroGuy923]

Timing chain tensioner is a common Ecotec failure. A new tensioner has a bolt head that bulges out, the old stock one has a flat head.

I'm confused. Is this all I need?
https://www.dormanproducts.com/p-86802-917-954.aspx

 

[Mayor West]

I'm confused. Is this all I need?
https://www.dormanproducts.com/p-86802-917-954.aspx

Yeah