V1 Nukers City Goblin - 2009 SS/TC number 2 build

[TheNuker]

#2 looks like the AC refrigerant pressure sensor
#3 looks like the AC compressor clutch
#4 looks like an O2 sensor.

I can't see the pins enough on #7 to compare them to electrical connectors list.

I think your right for sure about the second O2 sensor plug, I just noticed that the upstream and downstream have different plugs. I just ordered the upstream one now. Thank you!

So far found this

#1.1 Red/blue EVAP not needed on goblin
#1.2 all black with metal clip EVAP not needed on goblin
#2 AC refrigerant pressure switch (basing these off locaiton I think your right jamesm)
#3 AC compressor clutch (basing these off locaiton I think your right jamesm)
#4 Upstream O2 sensor - sensor missing ordered.
#5 Ambient temp sensor- missing sensor ordered
#6 Blue/Gray - Backup sensor - sensor ordered was not included on new transmission.

Just missing #7 now. thank you everyone so far.

Nuker-

 

[TheNuker]

Over flow tank runs over to the nipple on right side of engine, I didn’t get one on my new engine either.
other connection runs to plug by MAP sensor pipe

Thank you, Any idea on that part number for that overflow nipple?

Nuker-

 

[jennam]

Can you post a picture of the end of #7? I can’t see how many pins it has.

 

[Gtstorey]

Thank you, Any idea on that part number for that overflow nipple?

Nuker-

Mine did come with that fitting, but it's one of the few things I've lost through this process. Here is what I ordered that worked;
Double Banjos and bolt washers,14 X 1.5 Thread. Bolt head 19mm. line 10mm ID | eBay

 

[Rauq]

#7 looks like one of the 5-pin connectors that is unfortunately the same design for the MAF and the sub-harnesses for both the coil packs and the injectors. If that's the case then you can either narrow it down by process of elimination or checking wire colors.

 

[TheNuker]

Mine did come with that fitting, but it's one of the few things I've lost through this process. Here is what I ordered that worked;
Double Banjos and bolt washers,14 X 1.5 Thread. Bolt head 19mm. line 10mm ID | eBay

Thanks for that one the GM part is gm 12593792 and its like 53$! For a freaking bolt with nipple. Crazy ****!

Nuker-

 

[Zoom Zoom]

Thank you, Any idea on that part number for that overflow nipple?

Nuker-

No I took the one off my old engine

 

[TheNuker]

#7 looks like one of the 5-pin connectors that is unfortunately the same design for the MAF and the sub-harnesses for both the coil packs and the injectors. If that's the case then you can either narrow it down by process of elimination or checking wire colors.

 

[jennam]

That looks like the MAP sensor connector.

 

[TheNuker]

That looks like the MAP sensor connector.

Hmmm I think I have the 2 map sensors plugged in right just verified they are different plugs then this one.
What attaches to this tube that DF provides for the lower TMAP sensor there is another port kinda like what a brass nipple would screw into.

 

[jennam]

I scanned back through my connector list and compared the wire colors. That actually looks to be the cam position sensor connector.

 

[Gtstorey]

I scanned back through my connector list and compared the wire colors. That actually looks to be the cam position sensor connector.

View attachment 21963

View attachment 21964

Looking at my car right now and I’m pretty sure it’s the front cam position. Although my grey wire isn’t very grey.

 

[Zoom Zoom]

Hmmm I think I have the 2 map sensors plugged in right just verified they are different plugs then this one.
What attaches to this tube that DF provides for the lower TMAP sensor there is another port kinda like what a brass nipple would screw into.

One of the GM STAGE 1 Sensors hook to that one and the other one here
and then the MAP sensors here

 

[TheNuker]

Yep you're right I feel stupid LOL I thought I had them both plugged in and could not see the front one. Yeah sure enough.... That means I have no outstanding plugs or sensors!

Thanks everyone. Hoping to start this sucker this weekend.

Nuker-

 

[TheNuker]

got the intercooler mounted tonight now to figure out the piping.... can’t wait! LOL

Nuker-

 

[Desert Sasqwatch]

got the intercooler mounted tonight now to figure out the piping.... can’t wait! LOL

Nuker-

View attachment 22082

Air scoops on the side? Fans? Going to be warm back there.

 

[ATMironov]

Air scoops on the side? Fans? Going to be warm back there.

I'm curious too...

 

[r3drckt]

Justin reed mounted his A2A in the same spot. Though he also had 2 fans on it

 

[TheNuker]

Yep, I'll have 2 12" fans sucking air through, Eventually I'll probably make a box with scoops on the sides closing it in from the turbo/exhaust. TBH with the dead spot behind the seats I don't see it being much worse. I just never liked the big ugly IC up on top on the bars.

Nuker-

 

[TheNuker]

Justin reed mounted his A2A in the same spot. Though he also had 2 fans on it

Also that is kinda what I'm basing this on, I figured he is at the 500+HP level and its working for him, so I should be okay.